Lennox Mini-Split Installation Nationwide

Lennox Mini-Split Installation: The Alpharetta Owner’s Guide

Lennox mini-split installation in Alpharetta typically runs $3,500 to $7,500 installed, depending on the system’s tonnage, the number of indoor heads, and how far the line set needs to run. We stock Lennox-compatible equipment on our trucks and can usually schedule installation within a few days of your free estimate, not weeks. Most Alpharetta homeowners call us when their existing mini-split has stopped cooling a room, started leaking condensation onto the floor, or developed a refrigerant hiss they can hear from the sofa.

Call (478) 606-5046

Key Takeaways

• Installed Lennox mini-split systems in Alpharetta: $3,500 – $7,500, written price before work starts
• We’re an independent installer, not a Lennox subsidiary, so we match the right unit and parts to your home without brand pressure
• Every job includes shoe covers, drop cloths, and a photo of the clean-up before we leave
• Live person answers the phone 24/7 at (478) 606-5046

Which Lennox Models This Applies To

We install and service Lennox mini-splits across the current product line: the MLA and MPB single-zone series, the MLA Multi-Zone outdoor units, and the newer SL25KCV and MLA Heat Pump systems that Alpharetta homeowners increasingly choose for shoulder-season heating. If you have an older Lennox ComfortSense mini-split or a discontinued MPA series, we can still match replacement parts and indoor heads, though lead time on those can stretch a few days longer.

Here’s what matters for compatibility: the outdoor unit’s model number tells you the refrigerant type and capacity, but the indoor head’s dimensions and electrical specs must match the line set and the outdoor condenser within a specific tolerance. A 12,000 BTU indoor head off a 36,000 BTU multi-zone condenser won’t work correctly, even if the connectors physically fit. That’s the most common installation mistake we correct in Alpharetta homes, especially in Windward and Crabapple, where multi-zone setups are popular for sunrooms and converted garages. We always verify the full model number on the outdoor data plate, not just the series name, before ordering or installing anything.

On OEM versus aftermarket: for Lennox mini-splits, we recommend genuine Lennox line sets and electrical components. The flare fittings and drain pan assemblies are sized to Lennox spec, and we’ve seen aftermarket drain pans fail within two Georgia summers when the plastic doesn’t hold up to sustained humidity. For things like disconnect boxes, line-set covers, and condensate pumps, quality aftermarket parts from brands like DiversiTech work fine and keep your installed price honest.

Signs Your Lennox Mini-Split Installation Is Failing

• Water pooling on the floor or wall below the indoor head. This is almost always a clogged drain line or cracked drain pan. In Alpharetta’s summer humidity, a mini-split can pull a gallon of moisture out of the air in a day, so a small crack turns into a wet floor fast.
• The unit runs but blows room-temperature air. This points to a refrigerant leak in the flare connection or coil. Mini-splits are critically charged systems: the refrigerant amount must be exact, down to the ounce, or efficiency collapses.
• Ice forming on the indoor coil or line set. A frozen coil usually means low refrigerant, a dirty blower wheel, or restricted airflow from a clogged filter. Running it in this state can damage the compressor within weeks.
• A hissing or bubbling sound near the outdoor unit or along the line set. That’s refrigerant escaping. The flare fitting at the condenser is the usual culprit, especially on systems installed before 2018 when torque wrenches were less commonly used on mini-split fittings.
• The outdoor unit short-cycles: on for three minutes, off for one, on again. In a Lennox mini-split this often traces back to a failing thermistor or a control board misreading coil temperature. Leaving it short-cycling through a full Alpharetta cooling season raises your electric bill and shortens compressor life.

Replacement Cost & What’s Included

A full Lennox mini-split installation in Alpharetta runs $3,500 to $7,500. At the low end, that’s a single-zone 12,000 BTU heat pump with a short line set, straightforward wall mount, and no major electrical upgrades. At the high end, you’re looking at a multi-zone system with two or three indoor heads, a longer line set run through finished space, a new dedicated circuit, and a condensate pump where gravity drainage isn’t possible.

What drives the range more than anything in Alpharetta is line set length and access. Homes in neighborhoods like Windward and Kimball Bridge often have crawlspaces and finished basements that make the refrigerant lines run longer and slower to install. The electrical side matters too: mini-splits need a dedicated circuit, and if your panel is full we may need a subpanel, which adds labor and material dollars. Every Meadowsweet quote includes the equipment, line set, electrical disconnect, condensate drainage, pad or wall mount for the outdoor unit, and the full installation labor. The written price you get is the price you pay, and the work is covered by our 365-Day Done Right Promise.

DIY or Call Us?

There is almost no safe DIY path on a mini-split that involves refrigerant, flare fittings, or electrical work. R-410A and R-32 run at pressures that can cause serious frostbite burns and eye injury. By law in Georgia, refrigerant handling requires an EPA Section 608 certification, and the electrical side requires a permit in Alpharetta. What you can safely check yourself: confirm the filters are clean, verify the outdoor unit isn’t blocked by mulch or leaves, check that the drain line isn’t visibly clogged at the outlet, and make sure no furniture is blocking the indoor head’s return air. Anything beyond that is where we’d rather you call us than risk a flare-fitting leak that ruins a $2,000 indoor head. Luis Serrano and the crew are at (478) 606-5046, and we’ll tell you honestly whether it’s worth repairing or replacing.

FAQs